Advice of the manufacturer on washing, drying and storing. The label on the product always applies.
čištění, sušení a skladování
After use in saltwater, rinse dry wear in freshwater. After each use, hang dry wear inside out to dry. When the suit is dry, lightly brush the inside to remove sand and other debris. Then turn the garment right side out and let the outside dry; lightly brush off sand and dirt. After the garment is completely dry, store loosely folded in an airtight bag to reduce exposure to ozone, which is the main contributor to latex gasket failure. Store in a temperature and humidity controlled environment; the back of your closet is perfect. Do NOT hang for long term storage. Hangers can damage the neck gasket causing premature gasket failure. Do not store dry wear wet or damp. Wash seasonally (or when soiled) with a cleaner designed for waterproof/breathable fabric such as Gear Aid ReviveX Pro Cleaner. Drysuit zippers should be closed for storage and also when cleaning the suit.
Source: immersionresearch.com
ochrana
Brush socks and shorts or pants clean of debris before entering a dry suit. Always wear shoes over your dry suit socks. Do NOT walk around in dry suit socks without shoes. For extra protection, neoprene socks can be used, however you may need to opt for larger shoes.
Source: immersionresearch.com
čeho se vyvarovat a životnost
A well-made dry top or dry suit may last almost indefinitely, but latex gaskets do not. It is not uncommon for people to get 2 or 3 seasons out of a neck gasket or latex booties, and latex wrists can last 2 or 3 years longer. When they start to fail, the edges of the wrists and neck seals start to dry out and crack; on booties, creases start to crack. Send the garment for replacement before an unexpected blowout. According to the gasket manufacturer, aftermarket UV treatments typically only address UV exposure, which is only one of several causes of degradation; their study suggested gaskets would still fail due to ozone or other reasons just as fast, so UV treatments are probably not worth it. Keep sunscreen off them. Copper or copper alloys should not come in contact with latex. Storage temperatures should be less than 78 degrees. Moist storage conditions should be avoided. Protect from prolonged UV from natural and artificial light. Do NOT leave garments with latex gaskets inside a hot car. Mineral oils destroy latex – often found in hand lotions and moisturizers (including sunscreen with moisturizers). If you’re not sure what’s in it, don’t put it on your gasket. IR has seen cases of gaskets apparently destroyed by Armor-All. Latex booties are not meant to be used as shoes; wear a very thin sock over the latex bootie before slipping it into your shoe.
Source: immersionresearch.com
stříhání
Trim latex gaskets to make them larger, but do so carefully. Make your cut as even as possible following the trim lines. Remove one ring at a time. You can always remove more rings if needed, but you can't put them back on. Rings can identify trimmable wrist gaskets; you'll see these rings on the inside of the gasket. If your gaskets do not have these rings, DO NOT TRIM your wrist gaskets.
Source: immersionresearch.com
mazání a používání
The zipper is the most expensive part of a drysuit. Proper lubrication of the zipper dock should be done frequently. Spread a small amount of lube around the horseshoe, trying to fill the small holes, on both sides and where the horseshoe touches together. Be careful not to apply lube directly to the teeth and wipe away any excess. After application exercise the zipper 5–10 times. YKK also recommends paraffin wax on both the inside and outside of the zipper when closed; rub the wax along both sides and wipe away excess with a toothbrush. Take your time and do not yank excessively on the zipper. If it isn't running smoothly or has trouble fully docking, relube and wax first. For TiZip MasterSeal 10 (2017 and older IR suits), lubricate the docking end with original TIZIP lubricant on front, back and inside where they connect to the zipper chain; repeat before long-term storage leaving the slider closed. For YKK zippers (2018 and newer) follow YKK Aquaseal maintenance.
Source: immersionresearch.com
čištění a skladování
When storing your suit, the zippers should all be fully closed, and the suit should be folded loosely to avoid kinking the zipper. IR also recommends storage in a sealed container. When drying, it is acceptable to leave the zippers open to expedite this process; once dry, the suit should immediately be zipped up and stored. If you get sand or grit in the zipper, use soapy water and a toothbrush to get the sand out of the teeth. Do not use any hard implement to remove sand because that could damage the teeth.
Source: immersionresearch.com
čeho se vyvarovat
Do not expose any part of the dry wear to sunscreen, insect repellent, or oils. This contamination leads to premature fabric and latex failure. Impacts with rocks, sharp sticks and thorns can damage dry wear.
Source: immersionresearch.com
praní
Before washing, zip the front, pockets and pit zips completely and fasten any loose flaps and straps. Machine wash at 41 °C/40°C. Use a small amount of liquid detergent (about one ounce/30 ml per load, depending on water quality and load). Rinse twice and minimize spinning (400 rpm or lower). Don't use powder detergents, fabric softeners, stain removers, or bleach. Don't wash with heavily soiled clothing. Always follow the garment manufacturer’s care label as well.
Source: gore-tex.com
sušení, žehlení a obnova DWR
Tumble dry on a warm gentle cycle or line dry. Don't dry at a high temperature. Once dry, tumble dry for a further 20 minutes to reactivate the durable water repellent (DWR) treatment. If a dryer isn't available, iron the dry garment on a gentle setting with no steam, protecting the garment with a towel or cloth. If water doesn’t bead and run off after washing, reapply a DWR product (pump-spray or wash-in; Gore recommends pump-action rather than aerosol for environmental reasons), then tumble dry 20 minutes or iron as above to activate it.
Source: gore-tex.com
zvláštní péče
Washing GORE-TEX garments with persistent beading surfaces (e.g. GORE-TEX SHAKEDRY) is slightly different as they have no textile outer layer – the outer layer is the GORE-TEX membrane itself and there's no need for DWR. Machine wash on delicate cycle at 41 °C/40°C. Do not dry clean. Do not tumble dry. Do not iron. Do not bleach. Do not apply DWR treatment.
Source: gore-tex.com
čeho se vyvarovat
Do not use powder detergents, fabric softener or chlorine bleach. Gore does not recommend stain removers; instead use liquid detergent locally on stained areas or in a pre-wash, or soak in warm water with liquid detergent. Dry-cleaning does not harm GORE-TEX fabric, but always follow the garment manufacturer’s instructions; if professionally dry-cleaned, request clear distilled hydrocarbon solvent rinse and a DWR treatment with heat reactivation. Do not dry clean GORE-TEX SHAKEDRY. Home dry-cleaning kits are not recommended. Dirt, sunscreen lotion, bug repellents, detergents, campfire smoke and cooking odors diminish water repellency.
Source: gore-tex.com